M300 - 1 - 要保管 Keep this manual 取扱説明書 Installation manual この度は、EXEDY RACING CLUTCH をご購入いただきまして誠にありがとうございます。 ご使用前に必ずこの取扱説明書をよくお読み下さい。 また、この取扱
M300 - 10 - Be sure to apply "Adhesive 1324" to the thread ridges of the crank bolt for the Toyota vehicle before tightening it. Otherwise
M300 - 11 - 2) マツダ車 構成図⑥のF/Wに純正部品のカウンターウェイト(7ページ参照)を付属の専用ボルトにて固定します。 Mazda vehicle Fix the Mazda genuine counterweight (see page 7) to the flywheel N
M300 - 12 - ! 注意 CAUTION ディスクには方向がありますので、向きを間違えないよう十分注意して下さい。 ツイン用ディスクA:「T/M SIDE」 ツイン用ディスクB:「F/W SIDE」 トリプル用ディスク:「EXEDY」マーク 上記識別文字が、カバー側から見える方向に組み込
M300 - 13 - エンジン側パイロットに、芯出しバーをセットし各ディスクのスプラインの歯筋を揃えてセンターを出し構成図NO.①のクラッチカバーAssyを締め付け固定します。 芯出しバーには純正のメインドライブシャフトの使用を推奨します。 Set the centering bar to the
M300 - 14 - 《アドバイス》 «Advice» z ペダル位置を深くしたい場合(床側に近付ける) マスターシリンダー部のプッシュロッドを短く調整し、フリー時のペダル高さを下げる方向に調整する。 If the pedal position should be moved towards
M300 - 15 - 日産純正部品番号(クラッチスリーブ) Nissan genuine parts number (clutch sleeve) 30501-A3800 (12 mm) 30501-S0160 (22 mm) 30501-N1601 (14 mm) 30501-0H600 (
M300 - 16 - (The clutch is used under normal condition.) Especially, DO NOT remove the spring in the clutch operator. Otherwise, the preload working o
M300 - 17 - 9. ! 警告 WARNING 本製品は下記の使用限界を超えて使用した場合、破損又は走行不能となり、人命に関わる事故に繋がる恐れが有りますので、絶対に行わないで下さい。 Do not over use the clutch beyond the following limit
M300 - 18 - 《使用限界表》 «Operation limit list» 項目 Item 許容限界値 Limit 最大入力回転速度 Max. engine rpm 12000 r/mim ツイン Twin Sタイプ S type 830 Nm {85 kgm} Sタイプ S type 1
M300 - 19 - お問い合わせ先 For further information (株)エクセディ スポーツBC EXEDY Corporation Sports BC 〒572-0822 大阪府寝屋川市木田元宮1-1-1 1-1-1 Kidamo
M300 - 2 - 取り扱い説明書について Installation manual introduction 本製品を正しくお使い頂き、あなたや他の人々への危害や財産への損害を未然に防止する為の注意事項を記載しています。 This installation manual includes
M300 - 3 - 取り扱い上のご注意 Caution during handling 1. ! 注意 CAUTION 梱包から取り出す際には、製品が重いので取り扱いに注意して下さい。 As this product is heavy, handle carefully when rem
M300 - 4 - 適応車種及び商品品番 Applicable vehicle and model 適合車種 Applicable vehicle model メーカー Manufacturer 商品品番 Part No. クラッチサイズClutch size 車種 Vehicl
M300 - 5 - 構成部品及び構成図 Components and structural drawing 個数 Number of pieces 構成図NO. No. 部品名称 Description プル式 Pull type プッシュ式 Push type ① クラッチカバーAss
M300 - 6 -
M300 - 7 - 別途ご準備必要な部品 Parts required additionally メーカー Manufacturer 車種 Vehicle modelエンジン形式Engine model商品番号 Parts No. 準備必要部品 Parts required to be pr
M300 - 8 - 上記以外の準備部品 Parts to be prepared other than the above ones 1. プッシュ系日産車については14ページに記載のレリーズスリーブが必要となります。 Release bearings shown in page 14 are
M300 - 9 - 3. プル系ホンダ車のレリーズベアリング取付け Installation of release bearing to pull type Honda vehicle レリーズベアリングを構成図①のクラッチカバーAssyに取り付けます。必ず安定した台上で作業してください。 I
Comments to this Manuals